全文获取类型
收费全文 | 37708篇 |
免费 | 5303篇 |
国内免费 | 2733篇 |
专业分类
电工技术 | 3932篇 |
技术理论 | 1篇 |
综合类 | 2981篇 |
化学工业 | 8931篇 |
金属工艺 | 4359篇 |
机械仪表 | 1595篇 |
建筑科学 | 810篇 |
矿业工程 | 570篇 |
能源动力 | 1458篇 |
轻工业 | 2154篇 |
水利工程 | 289篇 |
石油天然气 | 1694篇 |
武器工业 | 367篇 |
无线电 | 6384篇 |
一般工业技术 | 5473篇 |
冶金工业 | 2115篇 |
原子能技术 | 406篇 |
自动化技术 | 2225篇 |
出版年
2024年 | 70篇 |
2023年 | 739篇 |
2022年 | 1030篇 |
2021年 | 1337篇 |
2020年 | 1442篇 |
2019年 | 1383篇 |
2018年 | 1253篇 |
2017年 | 1493篇 |
2016年 | 1511篇 |
2015年 | 1525篇 |
2014年 | 2092篇 |
2013年 | 2294篇 |
2012年 | 2589篇 |
2011年 | 2548篇 |
2010年 | 1816篇 |
2009年 | 2085篇 |
2008年 | 1953篇 |
2007年 | 2396篇 |
2006年 | 2272篇 |
2005年 | 1865篇 |
2004年 | 1561篇 |
2003年 | 1564篇 |
2002年 | 1322篇 |
2001年 | 1203篇 |
2000年 | 1036篇 |
1999年 | 806篇 |
1998年 | 731篇 |
1997年 | 650篇 |
1996年 | 539篇 |
1995年 | 519篇 |
1994年 | 452篇 |
1993年 | 304篇 |
1992年 | 297篇 |
1991年 | 229篇 |
1990年 | 209篇 |
1989年 | 197篇 |
1988年 | 89篇 |
1987年 | 57篇 |
1986年 | 48篇 |
1985年 | 41篇 |
1984年 | 45篇 |
1983年 | 28篇 |
1982年 | 33篇 |
1981年 | 24篇 |
1980年 | 23篇 |
1979年 | 5篇 |
1978年 | 6篇 |
1977年 | 6篇 |
1975年 | 5篇 |
1951年 | 13篇 |
排序方式: 共有10000条查询结果,搜索用时 109 毫秒
91.
为了深入研究渗硼层中硼化物的性能,采用真空感应熔炼法制备单相硼化物材料。观察分析制备的硼化物微观组织,测试其力学性能。采用MMU-5G型销-盘式摩擦磨损试验机,在干摩擦条件下,研究了不同载荷下单相硼化物的摩擦学性能,观察其磨损表面形貌特征,探讨其磨损方式。结果表明:制备的硼化物为单一相,试样纯度高,试样的平均显微硬度为HV2065,平均断裂韧性值为1.68 MPa·m1/2;硼化物的断口处没有宏观的塑性变形,断口齐平光亮,表现为脆性断裂特征;干摩擦条件下随着载荷从10 N增加到30 N,硼化物的摩擦因数先降低后增加,20 N载荷时达到最小值,而其磨损量随着载荷的增加不断上升;随着载荷从10 N增加到30 N,磨损表面的粗糙度先逐渐上升后急剧上升; 10~20 N载荷下,硼化物的磨损以磨粒磨损为主,而25~30 N载荷下,硼化物的主要磨损方式从磨粒磨损转变为脆性破损。 相似文献
92.
为改善相变储能过程中石蜡(PA)的熔化性能,向PA中添加少量膨胀石墨(EG)制备了4种配比的石蜡/膨胀石墨复合相变材料(PA-EG)。通过热物性分析筛选出合适配比的PA-EG,并对其和PA在水平管壳式相变储能单元中的熔化过程进行了实验研究。根据相变材料的温度场变化以及加权法计算得到的熔化分数变化,对比分析了添加EG前后PA的熔化性能,并探究了加热温度对相变材料熔化性能的影响。结果表明,PA-EG3的热导率比PA高了7倍,且两者的相变温度和潜热相差不大。PA-EG3熔化过程中的自然对流效应弱于PA,但是较高的热导率能够显著改善相变储能单元中下部的熔化,使得其整体熔化速度快于PA。当加热温度为80℃时,PA-EG3的熔化过程比PA缩短了78.16%。此外,降低加热温度会使PA和PA-EG3的完全熔化时间都显著增加,但相同条件下PA-EG3的增加幅度更小。 相似文献
93.
《Ceramics International》2020,46(8):11689-11697
In this research, vapor phase transport (VPT) was introduced as a facile, inexpensive method to produce ZnO micro/nanostructures from various Zn sources such as pure Zn and alpha brass pre-alloyed powders (Cu–20Zn and Cu–28Zn) at different processing temperatures of 930 °C–1050 °C. Simultaneous thermal analysis (STA) was carried out to investigate Zn evaporation and ZnO micro/nanostructure formation. STA results showed an exothermic peck at 711 °C and 728 °C for Cu–20Zn and Cu–28Zn, respectively, due to oxidation of the evaporated Zn element and formation of ZnO micro/nanostructures. X-ray diffraction results showed that high purity ZnO micro/nanostructures were successfully synthesized via VPT process and the crystallite size was increased from ~60 nm to ~100 nm with increasing processing temperature. Field emission scanning electron microscopy observations showed morphology (e.g. rods, column, tetrapods, and combs) and size of the synthesized micro/nanostructures were dependent on the Zn sources and processing temperature, in which average diameter of the synthesized ZnO structures was increased with increasing the processing temperature. The smallest (98 nm) and largest (603 nm) average diameters of synthesized ZnO micro/nanostructures were attained from the pure Zn and Cu–28Zn brass powders at 930 °C and 1050 °C, respectively. 相似文献
94.
随着我国石油需求量不断增加,致密油藏的开发也愈发重要。如何高效开发致密油藏是一项重点难点,其中致密油藏注天然气提高采收率是一个极具潜力的研究方向。因此,本文着重介绍以天然气作为能量补充介质在国内外的研究现状和应用现状,并且从两相特征等方面总结了理论研究中的一些机理,对致密油藏注天然气提高采收率的发展前景进行了一定的展望。 相似文献
95.
96.
《Ceramics International》2020,46(2):1722-1729
The room temperature abrasive wear behavior of three selected MAX phases, Ti3SiC2, solution strengthened Ti2.7Zr0.3SiC2 and Cr2AlC, is investigated by low velocity scratch testing using a diamond conical indentor with a final radius of 100 μm and a cone angle of 120° and applied loads of up to 20 N. All three materials showed a relatively low wear resistance in comparison to most engineering ceramics such as Al2O3, Si3N4 and SiC. For all three materials, the wear rate scaled more or less linearly with the applied load. The softer Ti3SiC2 with a hardness of 2.8 GPa showed the lowest wear resistance with extensive ploughing and grain breakout damage, both within and outside the direct wear track, in particular at the highest load. The hardest material, Ti2.7Zr0.3SiC2, with a hardness of 7.3 GPa, showed a 5 times better wear resistance. The Cr2AlC with a hardness of 4.8 GPa showed a wear resistance equal to or even better than that of the Ti2.7Zr0.3SiC2. The wear mechanism depends on the applied load and the microstructure of the MAX phase materials tested. For the Ti3SiC2 sample, a quasi-plastic deformation behavior occurs below a point load of 10 N, resulting in grain bending, kink band formation and delamination, grain de-cohesion, as well as trans-and intra-granular fracture near the scratch groove. At this load, the Ti2.7Zr0.3SiC2 and Cr2AlC MAX samples display plastic ploughing, grain boundary cracks and material dislodgments. 相似文献
97.
利用相图计算的CALPHAD方法和超音雾化制粉技术,在CuFeCoCr体系中设计并制备了一系列微米级复合粉体。通过热压烧结方法在烧结温度为950℃,烧结压力为45 MPa的工艺条件下成功获得块体复合材料。研究了块体复合材料中Cu含量对显微组织,热导率,热膨胀系数以及显微硬度的影响。结果表明:CuFeCoCr块体复合材料均由fcc富铜相和fcc富铁钴铬相组成。该系列复合材料经600℃时效处理8 h后,其热膨胀系数变化范围为5.83×10-6~10.61×10-6 K-1,热导率变化范围为42.17~107.53 W·m-1·K-1。其中Cu55(Fe0.37Cr0.09Co0.54)45复合材料表现出良好的综合性能,即其热膨胀系数和热导率分别为9.08×10-6K-1和91.09 W·m-1·K-1,与电子封装半导体材料的热膨胀系数相匹配。 相似文献
98.
选择相溶解技术是一种简单、经济、有效的微/纳结构制备方法,尤其是在超长径比、超深宽比和单晶微/纳结构制备方面具有独特的优势。其原理是提取两相或多相合金中的微/纳结构,尺寸调控主要在预制合金形成的过程中进行。本文在明确区分选择相溶解技术和去合金化的基础上,首次详细综述了选择相溶解技术在纳米颗粒、微/纳丝、微/纳米孔和微/纳通道制备方面的研究进展,并结合本课题组研究工作完善了其工艺流程,拓宽了其应用范围,丰富了微/纳结构种类,为该技术在微/纳结构制备领域的广泛应用奠定了基础。 相似文献
99.
利用Thermo-Calc软件对镍基耐蚀Hastelloy G3合金进行了热力学计算,系统研究了成分对平衡相析出的影响规律,并通过SEM和TEM对合金时效处理后的析出相进行了观察。结果表明,合金析出的平衡相主要为σ相、μ相、M6C和M23C6;Cr、Mo含量主要影响σ相和μ相析出量及开始析出温度;而C元素显著影响碳化物M6C和M23C6的析出行为;进一步通过试验研究了时效过程中析出相的析出规律。 相似文献
100.
Kang Du Jun Fan Zheng-Yu Zou Xiao-Qiang Song Wen-Zhong Lu Wen Lei 《Journal of the American Ceramic Society》2020,103(11):6369-6377
Low-permittivity Ca1−xSrxSnSiO5 (0 ≤ x ≤ 0.45) microwave dielectric ceramics were prepared via traditional state-reaction at 1400°C-1450°C for 5 hours. Moreover the microwave dielectric properties of SnO2 ceramic were obtained for the first time. SnO2 ceramic was difficult to densify, and SnO2 ceramic (ρrel = 65.1%) that was sintered at 1525°C exhibited the optimal microwave dielectric properties of εr = 5.27, Q × f = 89 300 GHz (at 14.5 GHz), and τf = −26.7 ppm/°C. For Ca1−xSrxSnSiO5 (0 ≤ x ≤ 0.15) ceramics, Sr2+ could be dissolved in the Ca2+ site of Ca1−xSrxSnSiO5 to form a single phase, and the partial substitution of Ca2+ by Sr2+ could improve the microwave dielectric properties of CaSnSiO5 ceramic. Secondary phases (SnO2 and SrSiO3) appeared at 0.2 ≤ x ≤ 0.45 and could adjust the abnormally positive τf value of CaSnSiO5 ceramic. The highest Q × f value (60 100 GHz at 10.4 GHz) and optimal microwave dielectric properties (εr = 9.42, Q × f = 47 500 GHz at 12.4 GHz, and τf = −1.2 ppm/°C) of Ca1−xSrxSnSiO5 ceramics were obtained at x = 0.05 and 0.45, respectively. 相似文献